If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
display error
there is something wrong with my direct 3d,it was fine but
recently when i tested direct 3d in dxdiag the first test fails withe message 'test failed at step 42(query for d3d):HRESULT=0x80004002(no interface)' System Information ------------------ Time of this report: 9/1/2004, 10:04:17 Machine name: Intel Operating System: Windows 98 (4.10, Build 2222) A Language: English (Regional Setting: English) System Manufacturer: n/a System Model: n/a BIOS: n/a Processor: Intel(R) Pentium(R) 4 CPU 1.60GHz Memory: 96MB RAM Page File: 115MB used, 1836MB available Windows Dir: C:\WINDOWS DirectX Version: DirectX 9.0c (4.09.0000.0904) DX Setup Parameters: Not found DxDiag Version: 4.09.0000.0904 32bit Display Devices --------------- Card name: S3 Graphics ProSavageDDR Manufacturer: S3 Graphics, Inc. Chip type: S3 ProSavage DDR Rev A DAC type: Internal Device Key: Enum\PCI\VEN_5333&DEV_8D04&SUBSYS_8D045333&REV_00\ 000800 Display Memory: 31.0 MB Current Mode: 1024 x 768 (32 bit)(optimal refresh rate) Monitor: SyncMaster Monitor Max Res: 1600,1200 Driver Name: s3_8m.drv Driver Version: 4.14.0010.0010 (English) DDI Version: 9 (or higher) Driver Attributes: Beta Retail Driver Date/Size: 12/26/2003 17:56:14, 305456 bytes WHQL Logo'd: No WHQL Date Stamp: None VDD: *vdd,*vflatd Mini VDD: s3vdd8m.vxd Mini VDD Date: , 0 bytes Device Identifier: {D7B75DD3-CE44-11CF-8930-0EADA1C2C935} Vendor ID: 0x5333 Device ID: 0x8D04 SubSys ID: 0x8D045333 Revision ID: 0x0000 Revision ID: 0x0000 Video Accel: ModeMPEG2_C ModeMPEG2_A ModeMPEG2_D Deinterlace Caps: n/a Registry: OK DDraw Status: Enabled D3D Status: Enabled AGP Status: Enabled DDraw Test Result: Not run D3D7 Test Result: Failure at step 42 (Query for D3D): HRESULT = 0x80004002 (No interface) D3D8 Test Result: The tests were cancelled before completing. D3D9 Test Result: The tests were cancelled before completing. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Error Messages | Greg Hall | General | 1 | July 27th 04 10:41 AM |
Please help! Display settings !! | Mitzi | Monitors & Displays | 12 | July 11th 04 05:19 AM |
error messages | brnfrdmom | Software & Applications | 4 | July 5th 04 08:22 PM |
Display error message | Curt | Monitors & Displays | 1 | June 24th 04 07:11 PM |
Scan Disk run without automatic error fix checked | Jay Eddins | Disk Drives | 2 | May 22nd 04 12:37 AM |