If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
PCMCIA card reader with SRAM card
I just installed a PCI adapter to use PCMCIA SRAM cards in my win98
desktop computer. Windows recognized both the adapter and the memory card and installed new drivers. I rebooted. Control panel-System reports the devices are there and working properly. The problem is that the drive has not been assigned a drive letter and doesn't show up in My Computer or Windows File Manager so I can't transfer files to or from the card. There is no icon for it that I can see other than one in the Task Bar that allows you to stop the drive for card removal. It works. What am I missing? |
#2
|
|||
|
|||
PCMCIA card reader with SRAM card
On Thu, 6 Mar 2008 20:04:37 -0800 (PST), Old Guy
put finger to keyboard and composed: I just installed a PCI adapter to use PCMCIA SRAM cards in my win98 desktop computer. Windows recognized both the adapter and the memory card and installed new drivers. I rebooted. Control panel-System reports the devices are there and working properly. The problem is that the drive has not been assigned a drive letter and doesn't show up in My Computer or Windows File Manager so I can't transfer files to or from the card. There is no icon for it that I can see other than one in the Task Bar that allows you to stop the drive for card removal. It works. What am I missing? Four suggestions: (1) Use TweakUI to check whether the higher drive letters are hidden. (2) Try executing "fdisk /status" in a DOS window. (3) Try "vol d:", where "d:" can be D:, E:, F:, etc. (4) Type the following line at the command prompt (it looks like two lines but is actually one long line). If required, respond with "Fail" to "Abort, Retry, Fail?". This should find all the existing drive letters, whether visible or hidden. command /c for %%i in (c d e f g h i j k l m n o p q r s t u v w x y z) do vol %%i: | find /i "volume" - Franc Zabkar -- Please remove one 'i' from my address when replying by email. |
#3
|
|||
|
|||
PCMCIA card reader with SRAM card
On Mar 6, 11:18 pm, Franc Zabkar wrote:
On Thu, 6 Mar 2008 20:04:37 -0800 (PST), Old Guy put finger to keyboard and composed: I just installed a PCI adapter to use PCMCIA SRAM cards in my win98 desktop computer. Windows recognized both the adapter and the memory card and installed new drivers. I rebooted. Control panel-System reports the devices are there and working properly. The problem is that the drive has not been assigned a drive letter and doesn't show up in My Computer or Windows File Manager so I can't transfer files to or from the card. There is no icon for it that I can see other than one in the Task Bar that allows you to stop the drive for card removal. It works. What am I missing? Four suggestions: Thanks very much. Sorry for taking so long to respond. (1) Use TweakUI to check whether the higher drive letters are hidden. I didn't have this program. I downloaded it and ran it. I saw no options that would be useful (2) Try executing "fdisk /status" in a DOS window. Only my non partitioned (primaryonly) C drive showed up. (3) Try "vol d:", where "d:" can be D:, E:, F:, etc. I tried this for every letter of the alphabet beyond D, my CD-ROM. All were invalid. (4) Type the following line at the command prompt (it looks like two lines but is actually one long line). If required, respond with "Fail" to "Abort, Retry, Fail?". This should find all the existing drive letters, whether visible or hidden. command /c for %%i in (c d e f g h i j k l m n o p q r s t u v w x y z) do vol %%i: | find /i "volume" I tried this a few times and kept getting "invalid parameter ( list of letters)" - Franc Zabkar -- Please remove one 'i' from my address when replying by email. Device Manager reports the following are all installed and working properly: Memory Technology Drivers SRAM Memory Card (series 1) PCMCIA Socket PCMCIA Card Services Ricoh RL5C475 Card Bus Controller The card is listed in Hardware in System Tools under Miscellaneous, not in Storage Devices. |
#4
|
|||
|
|||
PCMCIA card reader with SRAM card
Getting SRAM to work with Windows 98 can be difficult. This site has a good
description of the process - it isn't simple, however. http://www.synchrotech.com/support/f...-pc_cards.html (about halfway down). The MS link from that page no longer works but this may be helpful: http://support.microsoft.com/kb/142945/en-us Problems Installing SRAM or Flash Memory Cards in Windows 95 When you insert a PCMCIA SRAM or Flash memory card into a Windows 95- based computer that has been configured to use protected-mode PCMCIA card drivers, there may be no drive letter in My Computer or Windows Explorer associated with the PCMCIA card. This can occur even though the card seems to be recognized properly and the appropriate driver is installed. The advice there (for W95) is exactly opposite to the advice on the previous page (for W98). However, here is an example of driver installation using the W95 technique in W98: http://support.microsoft.com/kb/264387/en-us -- Jeff Richards MS MVP (Windows - Shell/User) "Old Guy" wrote in message ... On Mar 6, 11:18 pm, Franc Zabkar wrote: On Thu, 6 Mar 2008 20:04:37 -0800 (PST), Old Guy put finger to keyboard and composed: I just installed a PCI adapter to use PCMCIA SRAM cards in my win98 desktop computer. Windows recognized both the adapter and the memory card and installed new drivers. I rebooted. Control panel-System reports the devices are there and working properly. The problem is that the drive has not been assigned a drive letter and doesn't show up in My Computer or Windows File Manager so I can't transfer files to or from the card. There is no icon for it that I can see other than one in the Task Bar that allows you to stop the drive for card removal. It works. What am I missing? Four suggestions: Thanks very much. Sorry for taking so long to respond. (1) Use TweakUI to check whether the higher drive letters are hidden. I didn't have this program. I downloaded it and ran it. I saw no options that would be useful (2) Try executing "fdisk /status" in a DOS window. Only my non partitioned (primaryonly) C drive showed up. (3) Try "vol d:", where "d:" can be D:, E:, F:, etc. I tried this for every letter of the alphabet beyond D, my CD-ROM. All were invalid. (4) Type the following line at the command prompt (it looks like two lines but is actually one long line). If required, respond with "Fail" to "Abort, Retry, Fail?". This should find all the existing drive letters, whether visible or hidden. command /c for %%i in (c d e f g h i j k l m n o p q r s t u v w x y z) do vol %%i: | find /i "volume" I tried this a few times and kept getting "invalid parameter ( list of letters)" - Franc Zabkar -- Please remove one 'i' from my address when replying by email. Device Manager reports the following are all installed and working properly: Memory Technology Drivers SRAM Memory Card (series 1) PCMCIA Socket PCMCIA Card Services Ricoh RL5C475 Card Bus Controller The card is listed in Hardware in System Tools under Miscellaneous, not in Storage Devices. |
#5
|
|||
|
|||
PCMCIA card reader with SRAM card
On Mar 7, 6:12 pm, "Jeff Richards" wrote:
Getting SRAM to work with Windows 98 can be difficult. This site has a good description of the process - it isn't simple, however. http://www.synchrotech.com/support/f...-pc_cards.html (about halfway down). Thanks very much. I can't try all this until tomorrow. I'll post back then. |
#6
|
|||
|
|||
PCMCIA card reader with SRAM card
On Mar 7, 6:55 pm, Old Guy wrote:
On Mar 7, 6:12 pm, "Jeff Richards" wrote: Getting SRAM to work with Windows 98 can be difficult. This site has a good description of the process - it isn't simple, however. http://www.synchrotech.com/support/f...-pc_cards.html (about halfway down). Thanks very much. I can't try all this until tomorrow. I'll post back then. BINGO! Thanks very much. It wasn't difficult. |
#7
|
|||
|
|||
PCMCIA card reader with SRAM card
Thanks for letting us know that you got it sorted out.
-- Jeff Richards MS MVP (Windows - Shell/User) "Old Guy" wrote in message ... On Mar 7, 6:55 pm, Old Guy wrote: On Mar 7, 6:12 pm, "Jeff Richards" wrote: Getting SRAM to work with Windows 98 can be difficult. This site has a good description of the process - it isn't simple, however. http://www.synchrotech.com/support/f...-pc_cards.html (about halfway down). Thanks very much. I can't try all this until tomorrow. I'll post back then. BINGO! Thanks very much. It wasn't difficult. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Looking for a PCMCIA USB Card theat work with Win 98 (Not Win 98 SE) | RiptideHD | General | 2 | September 7th 07 09:07 PM |
Windows wont detect PCMCIA card | Fab | Plug & Play | 0 | April 3rd 07 03:58 PM |
pcmcia ATA Flash card reader find drive in WIN98 | cbork | Disk Drives | 0 | September 25th 04 03:11 AM |
Cannot install Netgear WG511 Wireless 32 bit PCMCIA card | David | Networking | 1 | August 5th 04 02:51 PM |
pcmcia network card problems | andy | Networking | 0 | June 21st 04 02:06 PM |