If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
win ME wont boot up
Hi...
can someone help me Please .My brother give me a computer for my daughter, it worked fine... untill we put "Labels Unlimited 2" onto it and attached my "HP Scanner" to it. Now when it boots up it will get to "WinMe" (as if its gonna start) the screen goes blank with the little line at the top (like its ready for u to type) the little line goes away, comes back, then goes and the screen remains blank... then it comes up on "safe mode", but it wont let me restore the computer to an earler date (although it asks if i want to do that) if i try to restore it just boots up like the above, and when "safe mode" comes up , it was unable to restore at this time (or something like that) prob due to "WinMe" wont load. can anyone help me Please. I dont have any cds or floppys with it,but have me boot floppy from my old computer but i wouldnt know how to use it anyway? I think it was the "LU2" that done something... as when loading it said it needed something else to run properly , so i clicked ok (as its not connected to the internet) so it would take from the LU2 cd. can anybody help me please! Liz |
#2
|
|||
|
|||
As System Restore isn't working, you *might* get away with it using the
scanreg /restore ploy. You could try reverting to the last 'good' registry prior to the problem happening, to see if that will bring things back again. Although it is possible do this in Normal and Safe Mode, under the circumstances I would suggest you do it in Real Mode DOS, using your WinMe Startup (floppy) Disk. .. but have me boot floppy from my old computer but i wouldnt know how to use it anyway? If you are sure that is a WinMe Startup (floppy) Disk then you should use it, if not go to http://www.bootdisk.com/bootdisk.htm and download the WinMe OEM option to your hard disk. Run it from your hard disk - with a fresh floppy disk in your A: drive - to create a WinMe Startup (floppy) Disk. Now try booting with your Windows Startup (floppy) Disk already inserted in the A: drive, and choose option 4) Minimal Boot. At the A:\ prompt, type "scanreg /restore" (no quotes and note the space between the g and /) then press Enter. Follow the screen prompts and when asked, select the LAST 'good' date BEFORE THE PROBLEM, continuing with the instructions. Don't forget to remove the floppy disk BEFORE you tell the machine to reboot. Hopefully, that should get things working again Mart "lizukuk" wrote in message ... Hi... can someone help me Please .My brother give me a computer for my daughter, it worked fine... untill we put "Labels Unlimited 2" onto it and attached my "HP Scanner" to it. Now when it boots up it will get to "WinMe" (as if its gonna start) the screen goes blank with the little line at the top (like its ready for u to type) the little line goes away, comes back, then goes and the screen remains blank... then it comes up on "safe mode", but it wont let me restore the computer to an earler date (although it asks if i want to do that) if i try to restore it just boots up like the above, and when "safe mode" comes up , it was unable to restore at this time (or something like that) prob due to "WinMe" wont load. can anyone help me Please. I dont have any cds or floppys with it,but have me boot floppy from my old computer but i wouldnt know how to use it anyway? I think it was the "LU2" that done something... as when loading it said it needed something else to run properly , so i clicked ok (as its not connected to the internet) so it would take from the LU2 cd. can anybody help me please! Liz |
#3
|
|||
|
|||
"lizukuk" wrote:
Hi... can someone help me Please .My brother give me a computer for my daughter, it worked fine... untill we put "Labels Unlimited 2" onto it and attached my "HP Scanner" to it. Now when it boots up it will get to "WinMe" (as if its gonna start) the screen goes blank with the little line at the top (like its ready for u to type) the little line goes away, comes back, then goes and the screen remains blank... then it comes up on "safe mode", but it wont let me restore the computer to an earler date (although it asks if i want to do that) if i try to restore it just boots up like the above, and when "safe mode" comes up , it was unable to restore at this time (or something like that) prob due to "WinMe" wont load. can anyone help me Please. I dont have any cds or floppys with it,but have me boot floppy from my old computer but i wouldnt know how to use it anyway? I think it was the "LU2" that done something... as when loading it said it needed something else to run properly , so i clicked ok (as its not connected to the internet) so it would take from the LU2 cd. can anybody help me please! Liz Boot the computer into Safe Mode. Then use Start - Run and enter the following command in the dialog box: SCANREGW /RESTORE Choose the most recent registry backup that is prior to your installing of "Labels Unlimited 2". Good luck Ron Martell Duncan B.C. Canada -- Microsoft MVP On-Line Help Computer Service http://onlinehelp.bc.ca "The reason computer chips are so small is computers don't eat much." |
#4
|
|||
|
|||
Hi... Sorry its took soo long 2 get back 2u's. After i printed ur replys....
this computer packed up (it was the fan), i tried..... scanreg /restore ploy I still couldnt get it 2 boot up... my son got it 2 boot in the end, by having the monitor unpluged b4 u boot up... then once u hear that windows has loaded, put the monitor back in. I tried restore again but it wouldnt let it restore... i left the monitor out when i done restore, waited a while then put monitor back in, it just said could not restore,no changes have been made 2 the computer. when i clicked "ok" windows started as normal. Thanku Liz "Mart" wrote: As System Restore isn't working, you *might* get away with it using the scanreg /restore ploy. You could try reverting to the last 'good' registry prior to the problem happening, to see if that will bring things back again. Although it is possible do this in Normal and Safe Mode, under the circumstances I would suggest you do it in Real Mode DOS, using your WinMe Startup (floppy) Disk. .. but have me boot floppy from my old computer but i wouldnt know how to use it anyway? If you are sure that is a WinMe Startup (floppy) Disk then you should use it, if not go to http://www.bootdisk.com/bootdisk.htm and download the WinMe OEM option to your hard disk. Run it from your hard disk - with a fresh floppy disk in your A: drive - to create a WinMe Startup (floppy) Disk. Now try booting with your Windows Startup (floppy) Disk already inserted in the A: drive, and choose option 4) Minimal Boot. At the A:\ prompt, type "scanreg /restore" (no quotes and note the space between the g and /) then press Enter. Follow the screen prompts and when asked, select the LAST 'good' date BEFORE THE PROBLEM, continuing with the instructions. Don't forget to remove the floppy disk BEFORE you tell the machine to reboot. Hopefully, that should get things working again Mart "lizukuk" wrote in message ... Hi... can someone help me Please .My brother give me a computer for my daughter, it worked fine... untill we put "Labels Unlimited 2" onto it and attached my "HP Scanner" to it. Now when it boots up it will get to "WinMe" (as if its gonna start) the screen goes blank with the little line at the top (like its ready for u to type) the little line goes away, comes back, then goes and the screen remains blank... then it comes up on "safe mode", but it wont let me restore the computer to an earler date (although it asks if i want to do that) if i try to restore it just boots up like the above, and when "safe mode" comes up , it was unable to restore at this time (or something like that) prob due to "WinMe" wont load. can anyone help me Please. I dont have any cds or floppys with it,but have me boot floppy from my old computer but i wouldnt know how to use it anyway? I think it was the "LU2" that done something... as when loading it said it needed something else to run properly , so i clicked ok (as its not connected to the internet) so it would take from the LU2 cd. can anybody help me please! Liz |
#5
|
|||
|
|||
Liz wrote :-
... when i clicked "ok" windows started as normal. Good to hear your machine is now working. Mart "Lizukuk" wrote in message ... Hi... Sorry its took soo long 2 get back 2u's. After i printed ur replys.... this computer packed up (it was the fan), i tried..... scanreg /restore ploy I still couldnt get it 2 boot up... my son got it 2 boot in the end, by having the monitor unpluged b4 u boot up... then once u hear that windows has loaded, put the monitor back in. I tried restore again but it wouldnt let it restore... i left the monitor out when i done restore, waited a while then put monitor back in, it just said could not restore,no changes have been made 2 the computer. when i clicked "ok" windows started as normal. Thanku Liz "Mart" wrote: As System Restore isn't working, you *might* get away with it using the scanreg /restore ploy. You could try reverting to the last 'good' registry prior to the problem happening, to see if that will bring things back again. Although it is possible do this in Normal and Safe Mode, under the circumstances I would suggest you do it in Real Mode DOS, using your WinMe Startup (floppy) Disk. .. but have me boot floppy from my old computer but i wouldnt know how to use it anyway? If you are sure that is a WinMe Startup (floppy) Disk then you should use it, if not go to http://www.bootdisk.com/bootdisk.htm and download the WinMe OEM option to your hard disk. Run it from your hard disk - with a fresh floppy disk in your A: drive - to create a WinMe Startup (floppy) Disk. Now try booting with your Windows Startup (floppy) Disk already inserted in the A: drive, and choose option 4) Minimal Boot. At the A:\ prompt, type "scanreg /restore" (no quotes and note the space between the g and /) then press Enter. Follow the screen prompts and when asked, select the LAST 'good' date BEFORE THE PROBLEM, continuing with the instructions. Don't forget to remove the floppy disk BEFORE you tell the machine to reboot. Hopefully, that should get things working again Mart "lizukuk" wrote in message ... Hi... can someone help me Please .My brother give me a computer for my daughter, it worked fine... untill we put "Labels Unlimited 2" onto it and attached my "HP Scanner" to it. Now when it boots up it will get to "WinMe" (as if its gonna start) the screen goes blank with the little line at the top (like its ready for u to type) the little line goes away, comes back, then goes and the screen remains blank... then it comes up on "safe mode", but it wont let me restore the computer to an earler date (although it asks if i want to do that) if i try to restore it just boots up like the above, and when "safe mode" comes up , it was unable to restore at this time (or something like that) prob due to "WinMe" wont load. can anyone help me Please. I dont have any cds or floppys with it,but have me boot floppy from my old computer but i wouldnt know how to use it anyway? I think it was the "LU2" that done something... as when loading it said it needed something else to run properly , so i clicked ok (as its not connected to the internet) so it would take from the LU2 cd. can anybody help me please! Liz |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Whoa. What was that? 98 load failure and.... | keith | General | 20 | March 3rd 05 06:46 AM |
Error msg: "Invaild System Disk - Replace disk and then press any | Alton | General | 2 | October 25th 04 11:31 PM |
windows 98se monitor prob | fortwilliam | General | 10 | October 21st 04 08:53 PM |
error message | bill | General | 7 | August 10th 04 02:09 AM |
No Info in Cofig.sys or Autoexec. | Ralph Jaggi | General | 84 | July 19th 04 09:44 PM |