ive been looking for support all over this site and have gotton no luck.... it's ridiculous, so this is my last resort... i have one simple question....my monitor has suddenly turned purple... everything has a purple tint, and everything ive tried with the colors doesnt help.... what could be...

I can not get the computer to communicate with the printer.. I have a laxmark x73 I tried to delete and reinstall and that does not work. I can make copies but not from the computer Can you help me?

Hi, I keep getting a error message that pops up while I am working in Windows 98 SE. The message is "MSBB caused an invalid page fault in module kernell 32 ddl at 017f:bff7a338". Can someone please provide some information or resolution on how to eliminate this error message. Thanks,

Many months ago I saw in display properties under the settings tab where it said "Extend My Windows Desktop onto this Monitor"..I put a check mark in the box and played around with it,unchecked the box again and clicked apply,I thought everything was ok...Now I'm unable to change...

Anyone knows how to disable the Display Properties? In other words how do I make it not to appear when one right clicks the desktop? Thanx

my computor froze while in safe mode and required turning off by the switch which has resulted in permanent safe mode status. How can I release it ? Any comments are welcome and thankyou in advance. Peter

I'm missing on my laptop the following file: "asivmsvc.vxd". Can someone tell me where I can dowload this file. Thank-you kindly

i cant figure out how to change the format of the icons, like how to make all zip files open differently...

please can someone help? wen i logged on my icons and text size was a loty smaller than normal. i tried to change through view...text size... but even at largest its very small and not as it should be....:( ty

I cannot set the video resolution above 640 =D7 480 with 16=20 colors and I don't know what to do... any help would be=20 grateful, the same computer had earlier on been set at=20 32bit true color. Thanks for your help. It's a code 23=20 problem with no solution button, how do I fix it?

Hopefully somebody here can help. I experimented with a dual monitor setup for about a week and then decided it wasn't working for me. Now that I have disabled and disconnected the second monitor everytime I startup my icons are not where I put them. I rearrange them back to how I want them and...

I need help with the following statement "Error extracting support files: Interface not registered". This first occured whilst trying to upload software for a epson printer (Photo RX500), and occurs everytime I try to upload further software. I tried all the methods I know to resolve this problem,...

When I open my display menu I only have 2 colors,2 and 16, I used to have many more, when I re-installed my windows they left, where do I get them

Since I didn't get any response to my earlier post about 32-bit display problem (12/29), let me ask another question. I downloaded the driver for my monitor on the chance that my driver has been corrupted. But now I can't figure the directions for reinstalling it. I get as far as a message...

MY DISPLAY IS MUCH TOO LARGE! AM UNABLE TO MOVE THE SLIDER IN SETTINGS AND RESOLUTION IS ONLY AVAILABLE IN 2 AN 16 COLORS. I HAVE RE-LOADED THE DRIVER FOR MY MONITOR...DIDN'T HELP. DISPLAY DRIVER PROBLEM, MAYBE??? PLEASE HELP!!!!!!!

When I try to close down windows 98, I get a pop up window stating: SUCHOSTP You must quit this program before you quit windows. I don't know what this program is? Please help to eliminate this. Thank you,

I am trying to fix a computer for a local Group Home. I am having a hard time because the buttons (such as the Next button, Cancel button, etc) are blank. The START button in the lower left hand corner also does not have any text. When by some chance I push the proper button, and it goes to a...

I gave my brother my old Windows 98 PC. It has a Matrox Millenium video card and the Matrox Powerdesk software. Somehow (he is definitely not computer literate) he has done something with the Powerdesk settings that make me think he has turned on the multiple desktop feature, but since I never...

I've lost my Quicklaunch toolbar and can't find any way of getting it back. Right clicking on the task bar and clicking on Quicklaunch puts the check mark beside it but it doesn't show up. Any idea what I've done and how to undo it?

all of a sudden, my taskbar (which ran along the bottom of the screen, where I like it) is running along the right side of the screen. I can't find anything in help that refers to this; how do I get it back to where it belongs?