Error Message.

[tom gillane]

I just got finished down loading a new McAfee Security
Center software. Each time I update, I must restart my
computer and it terminates rebooting with the following
error message: Windows could not upgrade the file %1 from %
2 %1: %2. Can any one help me with this problem?

[Mike M]

Your "Windows Could Not Upgrade the File %1 from %2 %1: %2" error:

First boot to DOS using a floppy and check whether you have a WININIT.INI
file in your C:\WINDOWS folder. If present rename it to something like
wininit.old and try booting again. It is also probable that you will have to
repeat the last software install or update that you made. See MS KB283069 -
"Error Message: Windows Could Not Upgrade the File %1 from %2 %1: %2
(http://support.microsoft.com?kbid=283069).

If you can't find a wininit.ini file then I suspect your problem is due to the
C:\_RESTORE\TEMP folder having around 64K files in it which is the limit
(2**16) for the number of files that can be located in a folder using the
FAT32 filing system. This then results in the "Cannot upgrade file %1 from
%2.." message when booting. I suggest you try deleting the _RESTORE folder
with the loss of any system restore checkpoints you might have (not that I
think they are now usable) and see if that solves the problem. Delete the
folder as follows:
a) Boot to DOS using a floppy. Do NOT choose "Minimal Boot" from the menu
when booting from a floppy but rather choose "Start computer with (or without)
CD-ROM support" otherwise the ATTRIB command will not be available.
b) At the DOS A:\> prompt, type:

ATTRIB -H -S -R C:\_RESTORE
and then
REN C:\_RESTORE OLDREST

c) Remove the floppy
d) Reboot your PC

Another problem is that the update you were doing was never completed so your
system may still be unusable and the update repeated.

e) Delete the folder C:\OLDREST
f) Check that an automatic system restore checkpoint was created.
g) Finally adjust the space allocated to the restore folder:
System | Performance | File System | Hard Disk and adjust the restore slider
to your preferred setting. A figure of 200MB is normally more than adequate
for day to day use allowing perhaps a week of checkpoints to be available
although increasing this to perhaps 400MB for a few days during periods of
large installs such Microsoft Office is advisable.
--?
Mike Maltby MS-MVP



tom gillane > wrote:

> I just got finished down loading a new McAfee Security
> Center software. Each time I update, I must restart my
> computer and it terminates rebooting with the following
> error message: Windows could not upgrade the file %1 from %
> 2 %1: %2. Can any one help me with this problem?

[Modulus]

Thank you... I had a customer(non-paying) with this ME=20
error about month ago but I was able to bypass this error=20
by pressing [ENTER] twice. No other problems after that=20
but the message still appears on boot-up.=20

I will use this the next time I experience this, of=20
course with a paying customer :-) =20
>-----Original Message-----
>Your "Windows Could Not Upgrade the File %1 from %2 %1: %
2" error:
>
>First boot to DOS using a floppy and check whether you=20
have a WININIT.INI
>file in your C:\WINDOWS folder. If present rename it to=20
something like
>wininit.old and try booting again. It is also probable=20
that you will have to
>repeat the last software install or update that you=20
made. See MS KB283069 -
>"Error Message: Windows Could Not Upgrade the File %1=20
from %2 %1: %2
>(http://support.microsoft.com?kbid=3D283069).
>
>If you can't find a wininit.ini file then I suspect your=20
problem is due to the
>C:\_RESTORE\TEMP folder having around 64K files in it=20
which is the limit
>(2**16) for the number of files that can be located in a=20
folder using the
>FAT32 filing system. This then results in the "Cannot=20
upgrade file %1 from
>%2.." message when booting. I suggest you try deleting=20
the _RESTORE folder
>with the loss of any system restore checkpoints you=20
might have (not that I
>think they are now usable) and see if that solves the=20
problem. Delete the
>folder as follows:
>a) Boot to DOS using a floppy. Do NOT choose "Minimal=20
Boot" from the menu
>when booting from a floppy but rather choose "Start=20
computer with (or without)
>CD-ROM support" otherwise the ATTRIB command will not be=20
available.
>b) At the DOS A:\> prompt, type:
>
>ATTRIB -H -S -R C:\_RESTORE
>and then
>REN C:\_RESTORE OLDREST
>
>c) Remove the floppy
>d) Reboot your PC
>
>Another problem is that the update you were doing was=20
never completed so your
>system may still be unusable and the update repeated.
>
>e) Delete the folder C:\OLDREST
>f) Check that an automatic system restore checkpoint was=20
created.
>g) Finally adjust the space allocated to the restore=20
folder:
>System | Performance | File System | Hard Disk and=20
adjust the restore slider
>to your preferred setting. A figure of 200MB is=20
normally more than adequate
>for day to day use allowing perhaps a week of=20
checkpoints to be available
>although increasing this to perhaps 400MB for a few days=20
during periods of
>large installs such Microsoft Office is advisable.
>--=81
>Mike Maltby MS-MVP

>
>
>tom gillane > wrote:
>
>> I just got finished down loading a new McAfee Security
>> Center software. Each time I update, I must restart my
>> computer and it terminates rebooting with the following
>> error message: Windows could not upgrade the file %1=20
from %
>> 2 %1: %2. Can any one help me with this problem?=20
>
>.
>

[Mike M]

Modulus > wrote:

> Thank you... I had a customer(non-paying) with this ME
> error about month ago but I was able to bypass this error
> by pressing [ENTER] twice. No other problems after that
> but the message still appears on boot-up.
>
> I will use this the next time I experience this, of
> course with a paying customer :-)


Only provided you split the profit. <VBG>
--
Mike Maltby MS-MVP